In PEM fuel cells and PEM electrolysers, the sealing of the MEA is critical for leak-tightness, performance, and service life. A suitable sub-gasket or subframe bonding solution reliably separates media, stabilizes the assembly, and must permanently withstand compression, temperature fluctuations, and moisture. CMC Klebetechnik develops thin, hydrolysis-stable adhesive films for this purpose that can be adapted to the installation space, material system, and manufacturing process.
When people talk about PEM fuel cells or PEM electrolysers, they usually think first of the membrane, catalyst, or bipolar plate. However, another area is crucial for the stack’s practical viability: the sealing of the membrane-electrode assembly, or MEA for short. This is because even minor leaks can cause media flows to mix, compromising operational safety and degrading the performance of the entire system.
The bonding around the catalyst-coated membrane (CCM) is therefore far more than just a joining task. It serves a sealing function within the stack, influences assembly quality, and helps ensure that the sensitive functional membrane can be controlled under real operating conditions.
What is the purpose of the bonding process in the MEA?
The MEA is the central component of a PEM fuel cell or PEM electrolysis cell. CMC describes it, in the context of its application, as an assembly consisting of CCM, gas diffusion layers, and a sub-gasket film.
The frame film in the subframe or sub-gasket area does more than just hold the unit in place. It seals the two sides of the MEA against each other, thereby preventing unwanted mixing of media between the anode and cathode sides.
This function is particularly critical in the PEM environment. The sealing zone must reliably separate the hydrogen and oxygen sides, prevent crossover, and at the same time fit into a highly precise stack architecture. The technical literature also describes the sealing structure of the MEA as a key factor influencing the performance and safety of PEM stacks.
Why is MEA sealing so important?
Because it must fulfill three functions simultaneously:
• Safely separate media
• Prevent leaks in the stack
• Support assembly and long-term stability
This makes the bonding process a functional element of the stack design, rather than just a connecting step.
What stresses act on the sealing zone in the stack?
CMC describes fuel cell and electrolysis stacks as “breathing” systems that are subject to constant expansion and contraction. The compression within the stack serves not only to ensure electrical contact but also, and crucially, to maintain the seal.
For the MEA seal, this presents a challenging combination of stresses:
Mechanical compression
The cells are pressed together with a specified clamping force. This force must prevent leaks and reduce contact resistance, but must not overload the GDL, the sealing zone, or the membrane.
Thermal Cycling
Temperature changes cause expansion and contraction in multilayer systems. This results in micro-movements that place continuous stress on the sealing structure.
Moisture and Hydrolysis
PEM applications are subject to constant exposure to moisture and chemicals. CMC therefore explicitly emphasizes the importance of hydrolysis-stable materials in the subframe and sealing areas.
Elektrische Isolation
The film used must not only provide a seal but also electrically insulate adjacent components.
These requirements demonstrate why the choice of materials in the MEA edge region should not be considered in isolation. The key factor is always the interplay between sealing performance, electrical insulation, mechanical behavior, and process capability.
How does the adhesive behave under pressure?
For this application, CMC supplies very thin, functionalized adhesive films for bonding CCM in fuel cells and PEM electrolysers. Such systems are of interest to users because they can adapt to surfaces and small relative movements. From a technical standpoint, this involves viscoelastic behavior: The adhesive exhibits both elastic and flow properties simultaneously.
The comparison with PTFE from the original text serves only as an analogy for time-dependent deformation under load. PTFE is generally known to be prone to cold flow or creep under sustained stress.
A thinly coated adhesive does not behave identically from a material standpoint. Nevertheless, the same principle applies here: Under compression and over time, the system must be designed so that adaptability does not come at the expense of the sealing function.
The behavior of such adhesive systems presents both opportunities and limitations:
Advantages
- Good adaptation to surfaces and micro-movements
- Very thin layers are possible
- Supports compact designs and low profile heights
- Can enable assembly-friendly lamination processes
What Developers Need to Keep in Mind
- Time-dependent creep or flow behavior under sustained load
- Influence of local pressure distribution and seal geometry
- Coordination with the carrier film, stack compression, and manufacturing process
- Resistance to moisture, temperature, and chemical exposure
In practice, this means that it is not a single parameter that determines performance, but rather the design of the entire system.
How can the bonding process be specifically integrated into the design?
The thinner and more functionally optimized an adhesive film is designed, the less impact it will have on assembly height and settling behavior. At the same time, the geometry of the sealing zone, the contact surface, the stiffness of the carrier film, and the local pressure distribution determine how stable the seal remains under actual operating conditions. The technical literature also emphasizes that the sealing structure, clamping force, and alignment with the bipolar plate must be considered together.
This is precisely where a film becomes a development challenge.
CMC coats the products in-house and can therefore implement the following customizations:
• Film material
• Adhesive system
• Thickness
• Coating structure
• Die-cutting geometry and delivery format
This is particularly relevant for development projects when the prototype design, process window, and subsequent series integration need to be planned together from the outset.
Why is CMC a development partner here rather than just a supplier?
In the fuel cell sector, a standard product is often insufficient. What matters most is how the material, coating, and geometry can be integrated into the specific stack. CMC positions itself in this field as a coating company specializing in technologically sophisticated solutions and works with customers to develop application- and product-specific designs for hydrogen technology.
This results in tangible added value for customers:
• Selection of suitable materials for the respective PEM application
• Adaptation to lamination and roll-to-roll processes
• Solutions for limited installation spaces and reproducible assembly
• Support in transitioning from prototype stages to robust series production processes
Further details on these topics can also be found in the CMC articles on hydrogen technology, production guidance for MEA designs, and subgasket films.
Fazit:
Sealing the MEA using an adhesive is a key design challenge in PEM fuel cells and PEM electrolysers. It separates media, stabilizes the assembly, and must function reliably over the long term under compression, temperature fluctuations, and humidity. Focusing solely on adhesion is not enough. The decisive factor is the coordinated interaction between the adhesive, the carrier film, the sealing geometry, and the process.
CMC Klebetechnik supports companies not only with an adhesive film but also with expertise in coating and application techniques throughout the entire development chain. This is particularly valuable when a functional prototype needs to be transformed into a reproducible, mass-producible stack solution.